Difference between revisions of "OLT"

From Catatan IBM
Jump to navigation Jump to search
(Created page with "==command line== 1. check ont status show gpon onu state gpon-olt_1/2/3 2. check ont power show pon power attenuation gpon-onu_1/2/3:18")
 
Line 6: Line 6:
2. check ont power
2. check ont power
  show pon power attenuation gpon-onu_1/2/3:18
  show pon power attenuation gpon-onu_1/2/3:18
3. check power interface
show interface optical-module-info gpon-olt_1/1/1
4. check ont mac address
show mac gpon onu gpon-onu_1/2/3:18
5. chesk ont uptaime and ont history logs
show gpon onu detail-info gpon-onu_1/2/3:18
6. find ont by SN number
show gpon onu by sn ZTEGC123456F
7. check ont version
show gpon remote-onu equip gpon-onu_1/2/3:18
8. check OLT uptime
show system-group
9. check olt board
show card
10. check OLT prosessor and memory
show processor
11.check olt card temperature
show card-temperature
12. check olt per slot
  show card slotno 2
13. check ont ip routing mode
show gpon remote-onu ip-host  gpon-onu_1/2/1:3
14. check ont konfig
show run int gpon-onu_1/4/1:2
15. reboot ont
config t
pon-onu-mng gpon-onu_1/2/1:3
reboot
16. reset factory ont
config t
pon-onu-mng gpon-onu_1/2/1:3
restore factory
17. disable/shutdown port ont
config t
pon-onu-mng gpon-onu_1/2/1:3
interface eth eth_0/2 state lock --> disable/shutdown port number 2
18. enable/shutdown port ont
config t
pon-onu-mng gpon-onu_1/2/1:3
interface eth eth_0/2 state unlock --> enable port number 2
19. release renew ont as dhcp client
config t    >>Enter configuration commands, one per line.  End with CTRL/Z.
pon-onu
pon-onu-mng gpon-onu_1/2/1:3
ip-host 1 dhcp-enable false ping-response false traceroute-response false
ip-host 1 dhcp-enable true ping-response true traceroute-response true
20. check rx/tx level uplink port
sho int optical-module-info xgei_1/21/1
21. reset slot card
reset-card slotno 2
22. swap
Use This for First Level Handling when you get Anomaly Process.
sometimes it can help you, but sometime isn’t
swap
23. show vlan summary
show vlan summary
24. check bandwidth profil
show gpon profile traffic

Revision as of 10:22, 28 January 2022

command line

1. check ont status

show gpon onu state gpon-olt_1/2/3

2. check ont power

show pon power attenuation gpon-onu_1/2/3:18

3. check power interface

show interface optical-module-info gpon-olt_1/1/1

4. check ont mac address

show mac gpon onu gpon-onu_1/2/3:18

5. chesk ont uptaime and ont history logs

show gpon onu detail-info gpon-onu_1/2/3:18

6. find ont by SN number

show gpon onu by sn ZTEGC123456F

7. check ont version

show gpon remote-onu equip gpon-onu_1/2/3:18

8. check OLT uptime

show system-group

9. check olt board

show card

10. check OLT prosessor and memory

show processor

11.check olt card temperature

show card-temperature

12. check olt per slot

 show card slotno 2

13. check ont ip routing mode

show gpon remote-onu ip-host  gpon-onu_1/2/1:3

14. check ont konfig

show run int gpon-onu_1/4/1:2

15. reboot ont

config t
pon-onu-mng gpon-onu_1/2/1:3
reboot

16. reset factory ont

config t
pon-onu-mng gpon-onu_1/2/1:3
restore factory

17. disable/shutdown port ont

config t
pon-onu-mng gpon-onu_1/2/1:3
interface eth eth_0/2 state lock --> disable/shutdown port number 2

18. enable/shutdown port ont

config t
pon-onu-mng gpon-onu_1/2/1:3
interface eth eth_0/2 state unlock --> enable port number 2

19. release renew ont as dhcp client

config t     >>Enter configuration commands, one per line.  End with CTRL/Z.
pon-onu
pon-onu-mng gpon-onu_1/2/1:3
ip-host 1 dhcp-enable false ping-response false traceroute-response false
ip-host 1 dhcp-enable true ping-response true traceroute-response true

20. check rx/tx level uplink port

sho int optical-module-info xgei_1/21/1

21. reset slot card

reset-card slotno 2

22. swap Use This for First Level Handling when you get Anomaly Process. sometimes it can help you, but sometime isn’t

swap

23. show vlan summary

show vlan summary

24. check bandwidth profil

show gpon profile traffic