OLT: ZTE C600 Basic Config
Step 1: Connect to the OLT
There is no factory IP address and usually no default user/pass like zte/zte, so the initial configuration must be done by serial terminal. For this connection you will use the port labeled CON.
The default password for the "enable" privilege is zxr10
[Ctrl-A is the prefix key] ************************************************************************* Welcome to ZXAN product C600 of ZTE Corporation ************************************************************************* Last login time is 07.28.2025-10:29:54-UTC, 0 authentication failures happened since that time. ZXAN>enable Password: zxr10 ZXAN#
- Delete Saved Configurated Data (Optional)
ZXAN# delete /datadisk0/DATA0/startrun.dat Are you sure to delete file(s)?(Yes/no): yes
- Than Restart OLT
ZXAN# reload system force proceed with reloading system? (Yes/no): yes
Step 2: Configure an IP Address on the mgmt_eth interface
Configure an IP Address on the mgmt_eth interface, and add a default gateway, then save the configuration. The default gateway must be added in "vrf mng" only if the management interface (mgmt_eth) will be used. If you will use a VLAN interface for management, "vrf mng" is not necessary.
ZXAN# conf t ZXAN(config)# interface mgmt_eth ZXAN(config-if)# ip address [IP] [Netmask] ZXAN(config-if)# exit ZXAN(config)# ip route vrf mng 0.0.0.0 0.0.0.0 [IP of the GATEWAY] ZXAN(config)# exit ZXAN# write Write DB OK! Building configuration... ....[OK]. ZXAN#
Verify the status of the cards using the command: show card (following is an example)
ZXAN#show card Shelf Slot CfgType CardName Port HardVer Status --------------------------------------------------- 1 1 GFBL B01GFBL 16 V1.0.0 INSERVICE 1 10 SFUC B02SFUC 4 V1.0.0 STANDBY 1 11 SFUC B02SFUC 4 V1.0.0 INSERVICE 1 18 PRVR PRVR 0 V1.0.0 INSERVICE 1 20 PRVR PRVR 0 V1.0.0 INSERVICE 1 21 FCVDE-I FCVDE-I 0 V1.0.0 INSERVICE
- Menampilkan Status Card
ZXAN#show interface brief Interface Portattribute Mode BW(Mbps) Admin Phy Prot Description xgei-1/10/1 optical Duplex/full 10000 up up up xgei-1/10/2 optical Duplex/full 10000 down down down xgei-1/10/3 optical Duplex/full 10000 down down down xgei-1/10/4 optical Duplex/full 10000 down down down xgei-1/11/1 optical Duplex/full 10000 down down down xgei-1/11/2 optical Duplex/full 10000 down down down xgei-1/11/3 optical Duplex/full 10000 down down down xgei-1/11/4 optical Duplex/full 10000 down down down
- Mengaktifkan Port Uplink (xgei-1/10/1)
conf t interface xgei-1/10/1 no shutdown
Step 3: Membuat User dan Password
Create a local authentication template and a dedicated username/password. This user/pass will be used by myOLT to connect to your OLT.
conf t aaa-authentication-template 2001 aaa-authentication-type local exit aaa-authorization-template 2001 aaa-authorization-type local exit system-user authorization-template 1 bind aaa-authorization-template 2001 local-privilege-level 15 exit authentication-template 1 bind aaa-authentication-template 2001 exit user-name myOLT bind authentication-template 1 bind authorization-template 1 password [a strong generated password] exit
Step 4: Enable Telnet
conf t line telnet server enable
atau
conf t line telnet server enable listen 23 exit
Sampai disini, OLT sudah bisa dilakukan akses melalui telnet
Step 5: Menambah akses remote melalui VLAN Uplink (Optional)
you can configure an "in-band" IP address on a VLAN interface. This is useful when you want to manage the OLT using the same physical interface that is used for normal traffic of the customers. We do not recommend this scenario because if a loop happens in the ONT, undetected by the ONT/OLT and the uplink port is shutdown by the uplink device as a reaction to the loop, you will lose the IP connectivity with the OLT as well.
conf t vlan 60 exit interface vlan60 ip address [IP] [MASK] exit ip route 0.0.0.0 0.0.0.0 [IP OF THE GATEWAY] ## Opsi route bisa diabaikan##
Remember! The VLAN must be tagged on the Uplink that will be used
conf t interface xgei-1/10/1 switchport mode trunk switchport vlan 600 tag exit
- Checking the routing table:
show ip forwarding route
In case you want to delete the existing default gateway and add a different one:
conf t no ip route 0.0.0.0 0.0.0.0 ip route 0.0.0.0 0.0.0.0 [IP OF THE GATEWAY]