OLT: ZTE C320 Basic Config

From Catatan IBM
Jump to navigation Jump to search

Step One: Connect to the OLT

  • IP Address: 136.1.1.100
  • Username: zte
  • Password: zte

After login, if the console displays the sign ">" instead of "#" then the "enable" command will be additionally needed to be entered to gain high privilege mode. The default password for "enable" mode is zxr10. For connecting by Telnet: Connect an ethernet cable to the dedicated (out-of-band) management port of the OLT. This management port is typically labeled 10/100 or MNG. It is positioned near the CL1 or DIAG port. The 10/100 port is an isolated port, designed for management purposes only. This port cannot be used to transport the traffic of the customers.

Configure on your PC or on the ethernet port of the Mikrotik where the OLTs' management port is connected the IP address 136.1.1.1/255.255.255.0 . Verify connectivity by pinging 136.1.1.100, you should receive replies. Then connect to the OLT.

telnet 136.1.1.100
Trying 136.1.1.100...
Connected to 136.1.1.100.
Escape character is '^]'.

************************************************
Welcome to ZXAN product C320 of ZTE Corporation
************************************************

Username:zte
Password:zte
ZXAN>enable
Password:zxr10
ZXAN#


Step two: Enable plug-and-play detection of the OLT boards and add the chassis type

  • For C320 OLT
conf t
set-pnp enable
add-rack rackno 1 racktype C320Rack
add-shelf rackno 1 shelfno 1 shelftype C320_SHELF
  • For C300 OLT
conf t
set-pnp enable
add-rack rackno 1 racktype IEC19
add-shelf rackno 1 shelfno 1 shelftype IEC_SHELF

Verify the status of the cards using the command: show card

ZXAN# show card

Rack Shelf Slot CfgType RealType Port    HardVer SoftVer         Status
-------------------------------------------------------------------------------
1    1     2    GTGH    GTGHG    16      120700  V1.2.5P3        INSERVICE
1    1     3    SMXA    SMXA     3       131201  V1.2.5P3        INSERVICE
1    1     4    SMXA    SMXA     3       131201  V1.2.5P3        STANDBY


Step three: Configure a new management IP address on the (out-of-band) mng1 interface

conf t
interface mng1
ip address [IP] [MASK]

Reconnect to the OLT using the new IP address you assigned.

Add the default gateway and save configuration:

conf t
no ip route 0.0.0.0 0.0.0.0
ip route 0.0.0.0 0.0.0.0 [IP of the GATEWAY]
exit
write


Step four: Create a dedicated username/password. This user/pass will be used between SmartOLT and your OLT

conf t
username smartoltusr password (enter a strong password) max-sessions 16 privilege 15


Step five: Enable telnet service, that is usually factory disabled

conf t
no ssh server only

At this stage, your OLT is ready to be interconnected with SmartOLT system.

Open your smartolt.com site, go to Settings -- OLTs -- Add OLT. Fill in the fields displayed, and click the Save button.

  • Other settings (If you use SmartOLT, these are configured automatically, no need to configure them manually):
conf t
auto-write enable
auto-write 18:00:00 everyday
mib-compatibility iftable v2
ntp server 20.101.57.9 priority 1 version 4
ntp server 216.239.35.4 priority 2 version 4
ntp enable


Optional: Remote Management Melalui Uplink

you can configure an "in-band" IP address on a VLAN interface. This is useful when you want to manage the OLT using the same physical interface that is used for normal traffic of the customers. We do not recommend this scenario because if a loop happens in the ONT, undetected by the ONT/OLT and the uplink port is shutdown by the uplink device as a reaction to the loop, you will lose the IP connectivity with the OLT as well.

conf t
vlan 300
exit
interface vlan300
ip address [IP] [MASK]