OLT: ZTE C600 Basic Config

From Catatan IBM
Jump to navigation Jump to search

Step 1: Connect to the OLT

There is no factory IP address and usually no default user/pass like zte/zte, so the initial configuration must be done by serial terminal. For this connection you will use the port labeled CON.

The default password for the "enable" privilege is zxr10

[Ctrl-A is the prefix key]


*************************************************************************
Welcome to ZXAN product C600 of ZTE Corporation
*************************************************************************

Last login time is 07.28.2025-10:29:54-UTC, 0 authentication failures
happened since that time.

ZXAN>enable 
Password: zxr10
ZXAN#
  • Delete Saved Configuration Data (Optional)
ZXAN# delete /datadisk0/DATA0/startrun.dat
Are you sure to delete file(s)?(Yes/no): yes
  • Than Restart OLT
ZXAN# reload system force
proceed with reloading system? (Yes/no): yes

Step 2: Configure an IP Address on the mgmt_eth interface

Configure an IP Address on the mgmt_eth interface, and add a default gateway, then save the configuration. The default gateway must be added in "vrf mng" only if the management interface (mgmt_eth) will be used. If you will use a VLAN interface for management, "vrf mng" is not necessary.

ZXAN# conf t
ZXAN(config)# interface mgmt_eth
ZXAN(config-if)# ip address [IP] [Netmask]
ZXAN(config-if)# exit
ZXAN(config)# ip route vrf mng 0.0.0.0 0.0.0.0 [IP of the GATEWAY]
ZXAN(config)# exit
ZXAN# write
Write DB OK!
Building configuration...
....[OK].
ZXAN# 

Verify the status of the cards using the command: show card (following is an example)

ZXAN#show card
Shelf Slot CfgType CardName     Port HardVer Status
---------------------------------------------------
1     1    GFBL    B01GFBL      16   V1.0.0  INSERVICE
1     10   SFUC    B02SFUC      4    V1.0.0  STANDBY
1     11   SFUC    B02SFUC      4    V1.0.0  INSERVICE
1     18   PRVR    PRVR         0    V1.0.0  INSERVICE
1     20   PRVR    PRVR         0    V1.0.0  INSERVICE
1     21   FCVDE-I FCVDE-I      0    V1.0.0  INSERVICE
  • Menampilkan Status Card
ZXAN#show interface brief
Interface      Portattribute  Mode  BW(Mbps)  Admin Phy   Prot  Description 
xgei-1/10/1    optical    Duplex/full  10000  up    up    up    
xgei-1/10/2    optical    Duplex/full  10000  down  down  down  
xgei-1/10/3    optical    Duplex/full  10000  down  down  down  
xgei-1/10/4    optical    Duplex/full  10000  down  down  down  
xgei-1/11/1    optical    Duplex/full  10000  down  down  down   
xgei-1/11/2    optical    Duplex/full  10000  down  down  down  
xgei-1/11/3    optical    Duplex/full  10000  down  down  down  
xgei-1/11/4    optical    Duplex/full  10000  down  down  down  
  • Mengaktifkan Port Uplink (xgei-1/10/1)
conf t
interface xgei-1/10/1
no shutdown


Step 3: Membuat User dan Password

Create a local authentication template and a dedicated username/password. This user/pass will be used by myOLT to connect to your OLT.

conf t
aaa-authentication-template 2001
aaa-authentication-type local
exit

aaa-authorization-template 2001
aaa-authorization-type local
exit

system-user
authorization-template 1
bind aaa-authorization-template 2001
local-privilege-level 15
exit

authentication-template 1
bind aaa-authentication-template 2001
exit

user-name myOLT
bind authentication-template 1
bind authorization-template 1
password [a strong generated password]
exit


Step 4: Enable Telnet

conf t
line telnet server enable

atau

conf t
line telnet server enable listen 23
exit

Sampai disini, OLT sudah bisa dilakukan akses melalui telnet


Step 5: Menambah akses remote melalui VLAN Uplink (Optional)

you can configure an "in-band" IP address on a VLAN interface. This is useful when you want to manage the OLT using the same physical interface that is used for normal traffic of the customers. We do not recommend this scenario because if a loop happens in the ONT, undetected by the ONT/OLT and the uplink port is shutdown by the uplink device as a reaction to the loop, you will lose the IP connectivity with the OLT as well.

conf t
vlan 60
exit
interface vlan60
ip address [IP] [MASK]
exit
ip route 0.0.0.0 0.0.0.0 [IP OF THE GATEWAY]  ## Opsi route bisa diabaikan##

Remember! The VLAN must be tagged on the Uplink that will be used

conf t
interface xgei-1/10/1
switchport mode trunk
switchport vlan 600 tag
exit
  • Checking the routing table:
show ip forwarding route

In case you want to delete the existing default gateway and add a different one:

conf t
no ip route 0.0.0.0 0.0.0.0
ip route 0.0.0.0 0.0.0.0 [IP OF THE GATEWAY]